Seed node: theory and starting

Introduction

There are three types of nodes used in The Power Ecosystem:

Consensus nodes are an essential component of the Power DCloud infrastructure that connects to a chain and participates in consensus with other nodes to build blocks and perform computations of smart contracts and decentralized backend.
Seed nodes are the nodes that connect to a chain and provide a copy of the blockchain to users upon request, like a CDN network of decentralized RPC providers. Seed nodes serve as a network of decentralized RPC providers, connecting to a chain and providing a copy of the blockchain to users upon request, much like a CDN network. This ensures that users have access to a reliable copy of the blockchain for their needs.
Storage nodes are the nodes that store frontend code, NFT data, or files in a decentralized way. Decentralized Storage (DStorage) allows users to store files in a truly decentralized manner, eliminating the need for centralized Web2 Clouds, and giving the user control over the number of copies of the file that should be created. The files are stored with access through HTTP standards, allowing users to reach them through different software such as browsers.

Go to Nodes and chains basics page to get more information on types of nodes and chains.

Seed nodes theory

As determined above, Seed nodes store and spread the copy of blockchain data, but don't participate in Consensus on creating new blocks.

Seed nodes are necessary to undertake the extra-load caused by the increased quantity of users from the Consensus nodes, as well as minimize the security risks. So, the users connect to Seed nodes, receive their copy of blockchain data needed, and send their transaction into the blockchain.

How to use the Seed node?

To use the Seed node:

Check the prerequisites here.
Install Erlang (this step is applicable for Docker installation ONLY):

Before starting Tea Ceremony you need to set up your environment by installing Erlang. You will need Erlang to run the Tea Ceremony client. You will not be able to start the node and connect to the chain without Tea Ceremony. To install Erlang, run:
```
apt -y install erlang-base erlang-public-key erlang-ssl
```
Note

You need to install erlang-public key and erlang-ssl. Otherwise, Erlang will not operate properly!
Get the power CLI:
1. Get the power cli by running the following command:
```
sudo wget https://tea.thepower.io/tp -O /usr/local/bin/tp
```
2. Change the tp file mode to executable by running the following command:
```
sudo chmod a+x /usr/local/bin/tp
```
Generate private key by running the following command:
```
tp --genkey --ed25519
```
As a result of this action, you will get the tpcli.key file. This file contains your private and public keys. Here is an example of this file. DON'T use the keys specified in this example:
```
% cat tpcli.key
{privkey,"302E020100300506032B6570042204204B1F52826447066469E7DBCA4E95CB0A03A2998D268C27885364D4AD7B7B0A8E"}.
{pubkey,"302A300506032B6570032100667C84FB1195C73F97AE14430C2024490C0EA6490F6EC0C1DE3FAEB4B6B32251"}.
```
caution
You may share your public key when necessary, but never share your private key.

Backup the file and continue.

Replace the node.config file content with the following:

node.config
{tpic,#{peers => [],port => 1800}}.
{discovery,#{addresses => []}}.

{replica, true}.
% ====== [ here is an example of upstream configuration ] ======
% {upstream, [                                                                               [ uncomment this line after copying ]
%   "http://c1038n3.deinfra.net:1080/?genesis=4InSbdZywQX8ySEHoKdZis5ghsA2oakfL7fegeOgM3U",  [ uncomment this line and replace with proper data ]
%   "http://c1038n5.deinfra.net:1080/?genesis=4InSbdZywQX8ySEHoKdZis5ghsA2oakfL7fegeOgM3U"   [ uncomment this line and replace with proper data ]
% ]}.                                                                                        [ uncomment this line after copying ]
% ======= [ end of example ] =========

% ====== [ here is an example of hostname configuration ] ======
% {hostname, <Hostname>}. [ Uncomment this line and replace with proper data ]
% ======= [ end of example ] =========
{dbsuffix,""}.
{loglevel, info}.
{info_log, "log/info.log"}.
{error_log, "log/error.log"}.
{debug_log, "log/debug.log"}.
{rpcsport, 1443}.
{rpcport, 1080}.

caution

You need to replace:

hostname with your hostname;
<PEER_ADDRESS>. It is obtained from The Power Ecosystem bot.

Note

Use this guide for more information on node.config.

Run the following command:
```
grep priv tpcli.key >> node.config
```
caution
This and the following steps are crucial because you will NOT be able to start your node without node.config file. You can find more information about these files here.
Build and run the node using the following guides. Which guide to use depends on the way you've downloaded the node:
1. Use this guide to build and start the node using docker-compose (recommended for most users).
2. Use this guide to build and start the node from Docker image.
3. Use this guide to build and start the node from sources (for advanced users ONLY).
Note
We strongly recommend you to build and run the node using docker-compose. It will help you eliminate the possible errors and make it easier for you to build your node.

Seed node: theory and starting

Introduction​

Seed nodes theory​

How to use the Seed node?​

Introduction

Seed nodes theory

How to use the Seed node?